Download Free NetApp NS0-155 Exam Dumps VCE and PDF Collection from PassLeader (Question 121 – Question 135)

New and Valid for 100% Passing Ensure NetApp NS0-155 Dumps from PassLeader: (195 Q&As), PassLeader offer both NS0-155 VCE Dumps and NS0-155 PDF Dumps for Preparing for the NetApp NS0-155 Exam, 100% Valid and 100% Passing Guarantee.

More, you can download the latest PassLeader NS0-155 Exam Dumps Online for FREE:

Which two modes support using SnapMirror over multiple network paths? (Choose two.)

A.    Standalone
B.    Partner
C.    Multi
D.    Failover
E.    Give back

Answer: CD

Identify the two commands that could be entered on the SnapMirror destination storage system. (Choose two.)

A.    Options snapmirror.access on
B.    Options snapmirror.resync on
C.    Snapmirror initialize
D.    Snap mirror resync

Answer: CD

What is the maximum distance between a standard clustered pair at 2Bbps?

A.    100 meters
B.    10 meters
C.    50 meters
D.    500 meters

Answer: D

Which exportfs command will temporally export the resource while ignoring the options specified in the /etc/exports file?

A.    exportfs -v<;pat>;
B.    exportfs -u<path>
C.    exportfs -a<path>
D.    exportfs -i<;pat>;

Answer: D

Is NetApp storage Encryption supported in Data ONTAP 8.1.1 Cluster-Mode?

A.    No, but you can file a PVR to request support.
B.    No, it is targeted for a future release of Data ONATP.
C.    Yes, only with a special license installed.
D.    Yes, it has been supported since 8.0.1.

Answer: D

Which two cp types would indicate a busy storage system? (Choose two.)

A.    cp_from_log_full
B.    cp_from_busy
C.    cp_from_cp
D.    cp_from_timer

Answer: AC

There are three phases of Non Disruptive Volume Movement (NDVM). What is the correct sequence of these phases?

A.    Setup Phase, Mirror Phase, Cutover Phase
B.    Initialization phase, Copy Phase, Migrate Phase
C.    Begin Phase, Move Phase, Complete Phase
D.    Setup Phase, Data Copy Phase, Cutover Phase

Answer: D

Which statement describes the results of the SnapMirror resynce command?

A.    Resynchronization finds the newest common snapshot shared by the two volumes or qtree, and removes all newer information on the storage system on which the command is run.
B.    Resynchronization will cause the loss of all data written to the destination after the original base snapshot was made.
C.    Resynchronization will update the snapshot on the destination filer.
D.    Resynchronization will update the snapshot on the source filer.

Answer: A

If you were troubleshooting and wanted to look at SnapMirror log files, what is the path to these files?

A.    /vol/vol0/etc/log/snaplog/
B.    /vol/vol0/etc/snapmirror/
C.    /vol/vol0/etc/snaplog/
D.    /vol/vol0/etc/log/

Answer: D

Host multi-pathing describes a ____ solution that has at least two distinct ____ paths to a LUN.

A.    Token ring; physical
B.    FC SAN; virtual
C.    FC or IP SAN; virtual
D.    FC or IP SAN; physical

Answer: D
Fiber Channel (FC), FCoE and iSCSI encapsulate SCSI-3. FCoE and iSCSI further encapsulate the transport within IP; hence the term IP SAN. In computer storage, multipath I/O is a fault-tolerance and performance enhancement technique whereby there is more than one physical path between the CPU in a computer system and its mass storage devices through the buses, controllers, switches, and bridge devices connecting them. A simple example would be a SCSI disk connected to two SCSI controllers on the same computer or a disk connected to two Fibre Channel ports. Should one controller, port or switch fail, the operating system can route I/O through the remaining controller transparently to the application, with no changes visible to the applications, other than perhaps incremental latency.

Which two will allow you to read and analyze a packet trace file generated by the storage system? (Choose two.)

A.    WireShark
B.    Pktt
C.    Netmon
D.    Eternal View

Answer: AC

In a Fiber Channel configuration, the host’s HBA is referred to as the ____, and the storage system’s HBA to as the ____.

A.    Target; initiator
B.    Primary; secondary
C.    Initiator; target
D.    Secondary; primary

Answer: C

Which action will cause a currently in-sync SnapMirror relationship to fail out of sync?

A.    Running snapmirroe update on the source storage system.
B.    Running snapmirror release on the source storage system.
C.    Modifying the /etc/snapmirror.conf file for the relationship on the source storage system.
D.    Modifying the /etc/snapmirror.conf file for the relationship on the destination storage system.

Answer: D

You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which is the most likely explanation?

A.    Once the directory structure has been deleted, you cannot restore the file using single file SnapRestore.
You must now SnapRestore the volume.
B.    Snapshot copies have been created since the original directory structure was deleted.
C.    You must recreate the directory structure before trying to restore the file.
D.    You cannot restore a file to an alternate location.

Answer: C
You can restore a file only to the volume where it was originally located. The directory structure to which a file is to be restored must be the same as that specified in the path. If this directory structure does not exist, you must create it before restoring the file.

Which mechanism allows you to make LUNs available to some initiators and unavailable to others?

A.    LUN masking
B.    LUN grouping
C.    LUN cloning
D.    LUN hiding

Answer: A
Logical Unit Number Masking or LUN masking is an authorization process that makes a Logical Unit Number available to some hosts and unavailable to other hosts.

Trying the PassLeader NS0-155 Dumps in VCE and PDF for Your First Attempt and 100% Passing: (195 Q&As, VCE and PDF)

More, download new PassLeader NS0-155 Exam Dumps for FREE: